2-step garage drops the four-on-the-floor kick and leaves gaps that the swing fills in. It's less about sounds than about placement: where the kick lands, how late the hats sit, and how much space you leave. These are the settings and patterns that get you there. Everything here is stock FL Studio.
1. Set the tempo and swing first
UKG usually sits around 130 to 134 BPM. FL opens at 130, so you're already close. Set the tempo before you program anything, because swing is felt against the grid.
- In the Channel Rack there's a swing knob at the top. Turning it up delays the off-16ths on every channel in one go. Start low and raise it until the hats start to skip, not stumble.
- For more control, leave the global swing alone and nudge individual hat notes late by hand in the piano roll or step sequencer. Different hits can then swing by different amounts.
- Never swing the kick and snare as hard as the hats. The backbone should stay solid and the hats should do the shuffling.
2. The 2-step kick pattern
The classic 2-step skeleton is simple: kick on beat 1, a second kick halfway through beat 3, snare or clap on beats 2 and 4. That's it. Two kicks per bar instead of four is what gives it the walking, lopsided feel.
- Add a ghost kick just before beat 3 or on the last 16th of the bar at a low velocity. It makes the pattern roll without making it busy.
- Layer a second snare or a rim on an off-beat, quieter than the main one, to give the shuffle something to push against.
- Keep the kick short and punchy. A long tail eats the bass.
3. Shuffled hats and ghost notes
Closed hats on the 16ths are the shuffle. Program them on a 16-step row, then let the swing knob do the offset. After that, edit velocity in the graph editor under the step sequencer.
- Make the on-beat hats softer and the off-beat hats a touch louder, so the groove leans forward.
- Drop out a few hats entirely. Gaps matter more than extra notes.
- Put an open hat on one off-beat per bar, not every one.
- Add a shaker or a second quiet hat on a different pattern length (say 3 steps against the bar) for movement that doesn't repeat every bar.
4. A chopped vocal idea
The vocal chop is the hook in a lot of garage. You don't need a full vocal: a short phrase works if you cut it up.
- Drop a vocal sample into Slicex (or chop it by hand in Edison), then play the slices from the piano roll so you can rearrange the order.
- Play the slices on the off-beats, late, so they sit against the kick rather than on it.
- Pitch a slice up or down a few semitones with the channel pitch knob for a second voice. Keep it in the key of your bass.
- Use a short reverb send and a high-pass filter so the chops sit above the bass and kick.
Use a vocal you have the rights to, or a loop from the loop library.
5. The bass
UKG bass is usually deep, short and locked to the kick. A common approach is two layers: a clean sine sub for the weight, and a slightly gritty mid layer an octave up so it translates on small speakers.
- Keep notes short and leave a gap where the kick lands, so they take turns and don't mask each other.
- Follow the root notes of your chords, with an occasional off-beat jump to answer the drums.
- Low-pass the mid layer, and cut it below roughly 100 Hz so the sine owns the low end.
- Pull the bass back a touch and check on a phone speaker. If it vanishes there, the mid layer needs more.
If the low end sounds weak once it's all running, the fixes in why your 808 sounds weak apply to a sub bass here too.
6. Arrange it
Garage arrangements are patient. Start with the drums and a filtered chord, bring the bass in, and save the vocal for the moment the track opens up.
- Intro (8 bars) — hats, a quiet kick and the chords through a low-pass filter.
- Build (8 bars) — add the snare, open the filter, bring in the vocal chop.
- Drop (16 bars) — full drums, bass and chops.
- Break (8 bars) — pull the kick and bass, keep the chords and a single vocal chop.
- Second drop and outro — repeat the drop with one new element, then strip back to the drums.
For the general idea of turning a loop into sections, see arranging a loop into a full beat. The same logic applies at a different tempo.
Want to hear finished beats? Open the UKG beats in the store, already filtered to the garage ones.
- 130 to 134 BPM, swing set before you program.
- Kick on 1 and halfway through 3, snare on 2 and 4.
- Hats swung harder than the kick and snare.
- Hat velocities varied, a few gaps left in.
- Vocal chop played on the off-beats and high-passed.
- Short bass: sine sub plus a filtered mid layer.
- Arranged in 8 and 16-bar blocks with a break.